HOME → GENERAL
GENERAL

PCC vs MCC vs Sub-Distribution Board: Where Each Fits in an Industrial Power System

What is the difference between a PCC, an MCC and a sub-distribution board? See what each does, what it feeds, and how they connect in a simple single-line diagram.

PCC vs MCC vs Sub-Distribution Board: Where Each Fits in an Industrial Power System
Note: Real plants vary. Some run a second PCC or a bus coupler. Some feed an SDB from an MCC. Always follow your site's own single-line drawing.

1. PCC: the main distribution point

The PCC sits right after the transformer or generator. Everything downstream depends on it.
What it does:The PCC sits right after the transformer or generator. Everything downstream depends on it.
What it does:
  • Receives incoming power
  • Holds the main busbar
  • Splits power into large feeders
  • Protects with large breakers (often air circuit breakers, ACBs, or moulded-case circuit breakers, MCCBs)
Typical loads it feeds:
  • MCCs
  • Large motors
  • Sub-distribution boards
  • Capacitor banks or other big equipment
What to know:
  • It carries the highest currents in the plant.
  • It also faces the highest fault levels. A fault here releases serious energy.
  • It often has metering and bus-coupler arrangements.

2. MCC: the motor boss

An MCC groups motor starters in one place. Each motor gets its own cubicle (also called a bucket or module).
What one motor cubicle often contains:
  • Isolating device (switch or breaker)
  • Short-circuit protection
  • Contactor (switches the motor on and off)
  • Overload relay (protects the motor from overheating)
  • Control wiring, pushbuttons or PLC interface
Starter types you'll see inside:
  • Direct-on-line (DOL)
  • Star-delta
  • Soft starter
  • Variable frequency drive (VFD)
Why it exists: Motors need control as well as power. The MCC puts control, protection and power in one organised board.

3. Sub-distribution board: power for the smaller stuff

An SDB takes one incoming feeder and splits it into many small circuits.
What it feeds:
  • Lighting
  • Socket outlets
  • Small fans and air conditioners
  • Office or workshop equipment
What's inside:
  • Incomer switch or breaker
  • Miniature circuit breakers (MCBs)
  • Residual current devices (RCDs), where fitted for earth-leakage protection
  • Neutral and earth bars
An SDB is usually simpler and smaller. It serves one area, such as a workshop, a floor or a building block.

Side-by-side comparison

pcc-vs-mcc-vs-sub-distribution-board

How to tell which board you're standing at

Look at the front and ask three questions.
  1. Is there a big incomer breaker and a busbar? Likely a PCC.
  2. Are there rows of small cubicles with motor labels? Likely an MCC.
  3. Are there rows of small breakers with circuit names like "Lights" or "Sockets"? Likely an SDB.
Then confirm it on the board label and the single-line drawing. Never guess.

Common mistakes

  • Calling every panel "the MCC." It causes wrong isolation instructions.
  • Assuming an SDB feeds motors. Some do feed small motors. Check the drawing.
  • Treating a board as dead because one breaker is off. Other feeders and the busbar may still be live.
  • Skipping the drawing. Plants get modified. Drawings and reality can drift apart. Update them.

Safety boundary

This article is for understanding. It is not a work procedure.
  • Only qualified, authorised people should open or work on these boards.
  • Follow your site's lock-out/tag-out (LOTO) and permit-to-work rules.
  • Prove dead before you touch. Test the test instrument first, test the circuit, then test the instrument again.
  • Check ratings and arrangements against the manufacturer's documentation and the relevant standard. For low-voltage switchgear assemblies, that is usually IEC 61439.

Key Takeaway

PCC distributes, MCC controls motors, SDB feeds small loads. Know which board you're at, and match it to the single-line drawing.
Do this today: Find your site's single-line diagram. Trace one motor from the transformer, through the PCC, into its MCC cubicle. Write down each device on the way. If you can't trace it, you've found a gap worth fixing.