A motor trips on overload. Someone grabs a clamp meter and starts guessing. Another person turns up the relay setting.
Nobody has read the small metal plate on the motor. The nameplate answers half the questions before you open a single panel.
What is a nameplate?
It’s the metal or plastic plate fixed to the motor frame. It shows what the manufacturer rated the motor to do.
Here is a sample three-phase motor nameplate. The values are fictional but realistic.

The highlighted full-load current is the number you’ll use most. Layouts and labels vary by manufacturer and region. Some plates use “FLA” or “In” for current.
The key ratings, one by one
VoltageThe supply voltage the motor is designed for.
- Single value, like 400 V: run it at that voltage in the connection shown.
- Dual value, like 400/690 V (Δ/Y): the connection changes with the supply. Delta suits the lower voltage. Star suits the higher one.
Why it matters: The wrong voltage or wrong connection can overheat the winding or stall the motor. Always check the connection in the terminal box against the plate.
CurrentUsually the full-load current (FLC or FLA): what the motor draws at rated load and voltage.
Use it to:
- Set the overload relay (see our article on contactors, breakers and overload relays)
- Size cables and protection, with the manufacturer’s and site rules
- Judge a running motor. Measured current well above nameplate points to a problem.
If the plate lists two currents for two voltages, use the one for your supply.
FrequencyUsually 50 Hz in Nigeria. Speed is tied to frequency. A 60 Hz motor on 50 Hz, or the reverse, changes speed and may overheat or underperform. Check the plate before assuming.
PowerThe mechanical output at the shaft, in kW or horsepower (HP). It is not the power the motor draws from the supply.
Conversion for reference: 1 HP is about 0.746 kW.
Remember: Electrical input is higher than output because of losses. That’s what efficiency tells you.
SpeedThe rated speed at full load, in rpm. It sits slightly below the synchronous speed, the speed of the rotating magnetic field.
Quick formula: Synchronous speed (rpm) = 120 × frequency ÷ number of poles
| Poles | Synchronous speed at 50 Hz | Typical full-load speed |
|---|---|---|
| 2 | 3000 rpm | about 2900 rpm |
| 4 | 1500 rpm | about 1450 rpm |
| 6 | 1000 rpm | about 960 rpm |
| 8 | 750 rpm | about 720 rpm |
The sample plate shows 1450 rpm. That points to a 4-pole motor. The gap between synchronous and rated speed is called slip.
Troubleshooting use: A motor running much slower than rated speed under load is probably overloaded, or has a supply or winding problem.
Power factorWritten as pf, cos φ or PF. It shows how much of the current does useful work. A value of 0.84 means 84% of the apparent power turns into real power.
Why it matters: Low power factor raises current for the same output. Lightly loaded motors usually have worse power factor than fully loaded ones. Plate values apply at rated load.
EfficiencyHow much of the electrical input becomes mechanical output. The sample says 90.4%. The rest becomes heat.
Many plates also show an IE class (IE1 to IE4). A higher number means higher efficiency. Check how your manufacturer defines it.
Duty ratingHow the motor is allowed to run over time. It’s easy to overlook and costly to ignore.
- S1: continuous duty. It can run at rated load until it reaches a steady temperature.
- S2: short-time duty. It can run for a stated period, then needs to cool.
- S3 and others: intermittent duty, with a stated cycle.
A motor rated S2 and run continuously will overheat. If the plate shows a duty cycle, treat that as a real limit.
Other plate details worth reading
- Insulation class (B, F, H): the winding’s heat tolerance. F is common.
- IP rating (like IP55): protection against dust and water. Outdoor or washdown areas need a suitable rating.
- Ambient temperature: the surrounding temperature the rating assumes. Hot environments can require derating, so check the manufacturer’s guidance.
- Altitude: high sites may need derating.
- Service factor: a stated margin for occasional overload. Don’t use it as normal running.
- Frame size, weight, bearing type, mounting, serial number: useful for replacements and spares.
A 10-minute nameplate check
Do this before any troubleshooting.
- Photograph the plate. Plates fade, get painted over and vanish.
- Read voltage and connection. Compare with the supply and terminal links.
- Read full-load current. Compare with the overload relay setting.
- Check frequency and speed. Does it match the supply and the machine’s needs?
- Check duty and ambient. Is the motor used within its limits?
- Check IP rating. Is it suited to the area?
- Measure running current with a suitable meter, if safe. Compare with the nameplate.
- Look for mismatch. Rewound motors, replaced motors and adapted machines often have plates that no longer tell the truth.
What a mismatch can tell you
| What you see | Possible meaning |
|---|---|
| Running current far above FLC | Overload, mechanical drag, low voltage or a winding fault |
| Running current far below FLC | Light load, which is often normal |
| Speed below rated at full load | Overload, low voltage or a poor connection |
| Overload relay set far above FLC | Hidden risk. Check the setting. |
| Wrong connection for the supply | Overheating or poor performance |
| Motor hot but current looks fine | Check ambient, ventilation, duty rating and bearings |
Don’t treat this table as a diagnosis. It points you to what to check next.
Why you must check against equipment documentation
A nameplate is a starting point, not the final word.
- Plates can be wrong or unreadable. They fade and get damaged.
- Motors get rewound or replaced. The plate may no longer match.
- Some values need context. Starting current, torque curves and derating data live in datasheets.
- Drive-fed motors (on a VFD) may need extra checks. Standard plate ratings assume a sine-wave supply.
- Hazardous areas need certification markings and strict procedures.
Check the manufacturer’s datasheet or manual for details. Compare any critical setting with site procedures.
Safety boundary
This article explains how to read a nameplate. It’s not a work procedure.
- Only qualified, authorised people should work on motor terminals and circuits.
- Follow your site’s lock-out/tag-out and permit-to-work rules.
- Isolate, prove dead, then work. Don’t open a terminal box on a live motor.
- Take measurements only with suitable instruments and training.
- Don’t change overload settings or connections without checking the plate and the documentation.
Key Takeaway
Read the nameplate first. Voltage, current, speed, duty and connection explain many “mystery” motor faults before you pick up a tool.
Do this today: Find one motor on your site. Photograph its nameplate. Write down voltage, full-load current and speed. Then check the overload relay setting against the current. If the numbers don’t line up, find out why.