HOME → GENERAL
GENERAL

Contactor vs Circuit Breaker vs Overload Relay: Three Devices, Three Different Jobs

Contactors, circuit breakers and overload relays are not interchangeable. See what each does in a motor circuit and how they work together.

Contactor vs Circuit Breaker vs Overload Relay: Three Devices, Three Different Jobs

A motor keeps tripping. Someone says, "Just replace the breaker." Another says, "Swap the contactor." A third says, "Turn up the overload."

Each fix assumes the three devices do the same thing. They don't. Every device in a motor circuit has one job, and none can do another's job.

The short answer

  • Circuit breaker: protects against short circuits and isolates the circuit.
  • Contactor: switches the motor on and off.
  • Overload relay: protects the motor from slow overheating.

Think of a car. The contactor is the ignition. The overload relay is the  temperature gauge that stops the engine before it cooks. The circuit breaker is the airbag: it acts when something goes badly wrong, fast.

The motor circuit at a glance

contactor-vs-circuit-breaker-vs-overload-relay

Power flows down the page. The dashed trip signal shows the overload relay opening the contactor's coil circuit, not the main supply.

Note: This is a simplified layout. Real starters vary by motor size, starter type and manufacturer. Always follow your site drawings and the manufacturer's documents.

1. Circuit breaker: the fast protector

A breaker watches for sudden, huge current. A short circuit can send current far above normal in a fraction of a second. The breaker must cut it off quickly.

What it does:

  • Interrupts short-circuit current
  • Protects cables and equipment from fault damage
  • Lets you isolate the circuit manually

What it doesn't do well:

  • Switch a motor on and off all day. It isn't built for frequent operation.
  • Replace motor overload protection. Many breakers are sized to ride through motor starting current, so they won't catch slow overheating.

Types you'll see: MCB, MCCB and motor protection circuit breakers (MPCBs). An MPCB can combine short-circuit and overload protection in one device. That makes it a special case, so read its datasheet.

2. Contactor: the switch with a coil

A contactor is an electrically operated switch. When its coil gets power, an electromagnet pulls the main contacts closed. The motor starts. When the coil loses power, the contacts open. The motor stops.

What it does:

  • Switches motor current on and off
  • Allows remote or automatic control (buttons, PLCs, sensors)
  • Handles frequent operation

What it doesn't do:

  • It can't clear a short circuit by itself. The breaker or fuse upstream does that.
  • It gives no overload protection on its own.

Terminals to recognise:

  • Power side: 1/L1, 3/L2, 5/L3 in; 2/T1, 4/T2, 6/T3 out
  • Coil: A1 and A2
  • Auxiliary contacts: small contacts used for control logic, such as the "hold-in" contact

3. Overload relay: the slow-burn guard

A motor can run too hot without any fault in the wiring. Maybe the load is too heavy, a bearing is dragging, or a phase is lost. The current stays a bit high for minutes. That heat slowly damages the winding.

The overload relay senses current and reacts over time. The higher the current, the faster it trips.

What it does:

  • Monitors motor current
  • Trips after sustained overcurrent
  • Opens a small control contact (commonly marked 95-96, normally closed)

What it doesn't do:

  • It doesn't interrupt motor current itself. It tells the contactor to drop out.
  • It doesn't protect against short circuits.

Two settings to know:

  • Current setting: set from the motor nameplate's full-load current (FLC).
  • Trip class: how fast it trips under overload (for example, Class 10 or Class 20). Match it to the load and the manufacturer's guidance.

Reset type: manual or automatic. Automatic reset on a motor can restart it unexpectedly, so use it with care.

How they work together

Here's the sequence in plain steps.

  1. Start pressed. The coil gets power through the control circuit.
  2. Contactor closes. The motor runs.
  3. Normal running. All three devices stay quiet.
  4. Overload develops. Current stays too high for too long.
  5. Overload relay trips. Its 95-96 contact opens in the coil circuit.
  6. Contactor drops out. The motor stops.
  7. Short circuit happens (different event). The breaker trips instantly and cuts the supply.

The overload relay's contact sits in series with the contactor coil. That's why a tripped overload relay stops the motor without cutting the main supply.

Side-by-side comparison

Side-by-side-comparison-of-contactor-circuit-breaker
  • Use a breaker as a routine start-stop switch. It wears out. It isn't designed for that duty.
  • Rely on a contactor for fault protection. It may weld shut or fail under short-circuit current.
  • Expect an overload relay to switch the motor. It has no power contacts for that. It only signals.
  • Skip the overload relay because "the breaker will trip." The breaker may never notice slow overheating.

You need all three roles covered. Sometimes one device combines roles. Check the datasheet.

Troubleshooting pointers

When a motor won't run or keeps stopping, think in roles.

  • Breaker tripped. Look for a short circuit or earth fault. Don't just reset it repeatedly.
  • Contactor won't close. Check the coil supply, the control circuit and the overload relay contact.
  • Overload relay keeps tripping. Check the actual motor current, the load, a lost phase, the setting and the ambient temperature.
  • Contactor buzzes or chatters. Look at coil voltage, dirt and worn contacts.

Never "fix" nuisance trips by cranking the overload setting up. You'll hide the problem and risk burning the motor.

Safety boundary

This article explains concepts. It's not a work procedure.

  • Only qualified, authorised people should open starters or work on motor circuits.
  • Follow lock-out/tag-out and permit-to-work rules.
  • Isolate, prove dead, then work. Remember that control circuits may be fed from another source and stay live.
  • Check ratings, settings and wiring against the manufacturer's documentation and your site standards.

Key Takeaway

Breaker for faults, contactor for switching, overload relay for overheating. Each covers a gap the others leave open.

Do this today: Open the drawing for one motor on your site. Mark each of the three devices. Write one line for each: "I protect against..." or "I switch...". If any role is missing, ask why.